Passcertguide shares the latest Cisco CCNP Routing and Switching 300-135 exam dumps for free exam practice tests and online downloads!
“Troubleshooting and Maintaining Cisco IP Networks” 300-135 exam. Ready to pass the 300-135 exam please click https://www.pass4itsure.com/300-135.html (full exam dump)
Cisco 300-135 Exam pdf
[Apr PDF] Free Cisco 300-135 pdf dumps download from Google Drive: https://drive.google.com/open?id=1BEjdSe2trgeKOSImEOz15e6pMuYS9wGD
[Oct PDF] Free Cisco 300-135 pdf dumps download from Google Drive: https://drive.google.com/open?id=1cgtBFvRhusdMwV6wijwJomkbVvNOOzJ7
300-135 TSHOOT – Cisco: https://www.cisco.com/c/en/us/training-events/training-certifications/exams/current-list/tshoot2.html
Cisco 300-135 Online Exam Practice Questions
QUESTION 1
Drag the GRE tunnel state from the left onto its corresponding scenario on the right.
Select and Place:
Correct Answer:
QUESTION 2
You examine the port statistics on a Cisco Catalyst switch and notice an excessive number of frames are being
dropped. Which of the following are possible reasons for the drops?
A. Unknown destination MAC address
B. Bad cabling
C. MAC forwarding table is full
D. Port configured for half duplex
E. Port configured for full duplex
F. Network congestion
Correct Answer: BF
QUESTION 3
Refer to the exhibit. Which command will allow the administrator to log in using the device database authentication?
A. aaa authentication login default local
B. aaa authorization network default local
C. aaa authentication login default enable
D. aaa authorization exec default local
Correct Answer: A
QUESTION 4
What is the result if you configure two devices with the ntp server command?
A. Nothing will happen until one of the devices is configured with the prefer parameter.
B. The NTP protocol will determine which server is most reliable and will synchronize to that server.
C. The device with the highest priority will become the active server and the other device will become the backup
server.
D. The device with the lowest MAC address will become the active server and the other device will become the backup
server.
Correct Answer: B
QUESTION 5
The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client
2 to access the WEB Server at 209.65.200.241.
After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity,
FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the
209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
H. ASW2
Correct Answer: D
On R4, in the redistribution of EIGRP routing protocol, we need to change name of routemap to resolve the issue. It
references route-map OSPF_to_EIGRP but the actual route map is called OSPF->EIGRP. Since Client 1 is able to ping
the near-end interface of the router R4 but not the far-end interface, we can be reasonably certain that the fault
condition is with R4.
QUESTION 6
The implementation group has been using the test bed to do an IPv6 \\’proof-ofconcept1.
After several changes to the network addressing and routing schemes, a trouble ticket has been opened indicating that
the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2 (2026::102:1).
The fault condition is related to which technology?
A. NTP
B. IP DHCP Server
C. IPv4 OSPF Routing
D. IPv4 EIGRP Routing
E. IPv4 Route Redistribution
F. IPv6 RIP Routing
G. IPv6 OSPF Routing
H. IPV4 and IPV6 Interoperability
I. IPv4 layer 3 security
Correct Answer: G
As explained earlier, the problem is with route redistribution on R4 of not redistributing RIP routes into OSPF for IPV6.
QUESTION 7
Configuration on R1 interface Serial0/0/1 description Link to ISP ip address 209.65.200.224 255.255.255.252 ip nat
outside ip access-group edge_security in ! ip access-list extended edge_security deny ip 10.0.0.0 0.255.255.255 any
deny ip 172.16.0.0 0.15.255.255 any deny ip 192.168.0.0 0.0.255.255 any deny 127.0.0.0 0.255.255.255 any permit ip
host 209.65.200.241 any !
What is the solution of the fault condition?
A. add permit ip 209.65.200.224 0.0.0.3 any command to R1s ACL
B. Under the BGP process, bgp confederation identifier 65001 command
C. Delete the current BGP process and reenter all of the commands using 65002 as the AS number.
D. Under the BGP process, delete the neighbor 209.56.200.226 remote-as 65002 command enter the neighbor
209.65.200.226 remote-as 65002 command.
Correct Answer: A
QUESTION 8
Output showing line VTY 0 4 config with an access list applied `ip access-class 1 in\\’
ip access list permit tcp any any eq 22 ip access list permit tcp any any telnet Cisco engineer is trying to setup secure
access to the router but why is SSH failing?
A. access-list needs to be applied with access-group command.
B. access-list only allows telnet access.
C. They\\’re needed to be transport input ssh on line vty 0 4
D. https://www.pass4itsure.com/300-125.html
Correct Answer: C
QUESTION 9
What is the ping response to a transmitted echo that needed to be fragmented and fragmentation was not allowed?
A. U
B. M
C. …
D. D
Correct Answer: B
QUESTION 10
Refer to the exhibit.
PC was not configured to obtain default-gateway from the DHCP server. What can we do for PC to access the Internet?
A. Configure static ARP in gateway router
B. Configure dynamic ARP in gateway router
C. Configure proxy-ARP in gateway router
D. https://www.pass4itsure.com/300-135.html
Correct Answer: C
QUESTION 11
The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires both Client 1 and Client
2 to access the WEB Server at 209.65.200.241.
After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity,
FHRP services, and device security, a trouble ticket has been opened DSW1 will not become the active router for
HSRP
group 10.
Use the supported commands to isolated the cause of this fault and answer the following questions.
What is the solution to the fault condition?
A. Under the interface vlan 10 configuration enter standby 10 preempt command.
B. Under the track 1 object configuration delete the threshold metric up 1 down 2 command and enter the threshold
metric up 61 down 62 command.
C. Under the track 10 object configuration delete the threshold metric up 61 down 62 command and enter the threshold
metric up 1 down 2 command.
D. Under the interface vlan 10 configuration delete the standby 10 track1 decrement 60 command and enter the standby
10 track 10 decrement 60 command.
Correct Answer: D
On DSW1, related to HSRP, under VLAN 10 change the given track 1 command to instead use the track 10 command.
The reason that router DSW1 will not become the active router is because it is configured to track the 10.1.21.128
255.255.0.0 network. It should have been configured to track the 10.2.21.128 255.255.255.0 network. This can be fixed
by
replacing the Change “standby 10 track 1 decrement 60” command with the “standby 10 track 10 decrement 60”
command.
QUESTION 12
If you want to use GRE with IPSec which is compatible with NAT traversal?
A. MD5 mode
B. SHA mode
C. IPsec tunnel mode
D. tunnel transport
Correct Answer: C
QUESTION 13
—Output from config–service password-encryption ! line console password a123124 ! line vty 0 4 password asdfasf12
login transport input telnet ! What will happen if client A will telnet to this device.
A. Telnet will be successful
B. Telnet will fail because of missing user database
C. Telnet will fail because of missing aaa new model
D. Telnet will fail because only ssh is allowed
Correct Answer: A
Share Pass4itsure discount codes for free
About Pass4itsure!
Pass4itsure offers the latest exam practice questions and answers free of charge! Update all exam questions throughout the year,
with a number of professional exam experts! To make sure it works! Maximum pass rate, best value for money! It helps you pass the exam easily on your first attempt.
Summarize:
How do I pass the Cisco 300-135 exam? You need to be prepared for it!
You need the latest and most effective learning materials and proper practices to pass the 300-135 exam.
This exam certifies that the successful candidate has the knowledge and skills necessary to:
- Plan and perform regular maintenance on complex enterprise routed and switched networks
- Use technology-based practices and a systematic ITIL-compliant approach to perform network troubleshooting
Pass4itsure offers you the latest exam materials! You can use the materials to prepare to help you achieve excellent results!